Chat with us, powered by LiveChat
Browse Categories

Pressure Settings for EHU2507-40-N-903

Items Needed to Set Eco-Rich:

  • Screwdriver
  • Wrench

The following steps must be completed before any settings and adjustments can be made to your Eco-Rich:

1. Connect 3 phase power (200 VAC ~ 230 VAC)

2. Fill oil reservoir to correct oil level. (Oil Weight ISO32 ~ ISO 68)

3. Connect pressure and return lines.

4. Connect alarm wires from machine (most machines do not require this step).

5. Turn power on to the machine and hydraulic unit.

6. Make sure machine is in a standby state and is not actuating any valves or cylinders.

Initial Procedures

1. Break locknut "A" free, using a crescent wrench. Turn the overpressure adjustment valve "B" clockwise until the adjuster bottoms out, making sure the locknut "A" is not preventing you from bottoming out the overpressure valve. 

2. On the control panel, press the "mode" and "return" keys simultaneously and hold them for 2 seconds to get you into the parameter mode. You should see "P00" flashing on the screen. Use the "up" key and go to "P13" and press the "return" key. "P13" is the pressure setting parameter.

3. You will now see "PL.0" show on the screen. 

4. To set your desired pressure, press "up" or "down" key (acceptable pressure range is 1.5 MPa ~ 7.0 MPa) and then press "return" key.

5. Now you will see "QL.0" on the screen. Press the "return" key until you see "P13" on the screen again. 

6. Press the "mode" key and the screen should now show your desire pressure setting.

Setting the Motor RPM

1. Press the "mode" key to get into the monitor mode. You should see the "N00" flashing on the screen. 

2. Use the "up"or "down" key and screen to "N05". Press the "return" key. On the control panel, you will see the motor RPM represented by a 2 or 3 digit number on the screen. Please note that for the motor RPM, the last digit is dropped from the control panel screen. For example, if the screen shows "122" add a zero to the end of it to get the RPM. In this case, it would be 1220 RPM. 

3. Loosen locknut "C" free.

4. Take a flathead screwdriver to adjust the flow control valve "D". Slowly turn the flow control valve "D" clockwise to lower and counter-clockwise to raise until the motor RPM on the control panel shows 38, which is 380 RPM.

5. Lock the "C" locknut down. The motor RPM is now set.

Setting the Over Pressure Valve

1. With the motor RPM shown on the control panel screen, take the crescent wrench and slowly turn the overpressure valve adjustment "B" counterclockwise until you see the motor RPM start to rise above your setting of 38 (380 RPM).

2. Stop turning once you see the RPM raise and go back to the setting just before the breaking point where the motor RPM raised above 38.

3. Turn the overpressure valve adjustment "B" 3/4 revolution turn clockwise. Please note that if the overpressure valve adjustment "B" bottoms out before you can turn the adjustment 3/4 of a revolution turn, then take the distance that you can turn it until it bottoms out and divide it by half. This is the amount that is needed to turn the overpressure valve "B" back in clockwise. Please do not leave the overpressure valve bottomed out, as it will lead it not to operate. 

4. Lock the locknut "A" down.

5. Press the "mode" key. This will bring you back to your desired pressure setting where you started.

Congratulations. Your machine is now ready to run.

Please call 1 (815) 943-9111 or email for more questions.


2023 2022 2021 2020 2019 2018 2017 2016